Even though carpet installation should be done by professional service providers, with the right skills and tools the process becomes a DIY project. This floor covering is often done in two ways including the use of tacks and tack strips and by gluing directly on the surface. Generally, tacks are popular inside the building and gluing done if the carpet is to be fixed outdoors or to a slab having moisture.
This post describes the 12 necessary tools when laying carpet through a tack strip technique. Keep in mind most of the items can be hired instead of buying them. But if you are planning to do the installation in multiple homes then it is wise to get one. Keep reading this blog and toolsmasterblog.com to know what tools you need to lay carpet.
List of Tools to Lay Carpet
Removing old floor covering like carpeting laid wall to wall from a house is heavy and cumbersome. Thanks to the fact that it is commonly floated and not glued down, thus the DIY style is expected to continue. One tricky part when fixing the new flooring comes in precisely cutting the material to fit well in the room. Of course, a single slice done the wrong way can damage the entire piece. Next time, considering a utility knife for cutting the material in large sheets can save you some likely troubles.
All you will need to do is to cut from the flat and stiff backside. Roll up some part of the carpet, slice it carefully on the edge and carry it from the room. The process may take longer compared to rolling the carpet up. But carrying the small pieces for disposal is much easier. This makes a scratching place for pets or a foot mat.
The design of this utility knife particularly cuts and trims carpet seams and edges. It has a metal runner below, a handle above, and one edge has a blade. Simply press it flat along the carpet and the sharp end under the baseboard. And push it from end to end while applying pressure when working.
Once the installation is finished, it is common to find stray carpet fibers along the seams. The residual layers can be hazardous to you and make the floor look ugly. There are specialty shears for trimming off the imperfections properly and neatly.
It has an offset handle that prevents unintended scratching while napping and the loops are well-sized. So, you have no worry if you have large fingers as you can easily grip the tool. Its blades are made from carbon steel to ensure durability and provide money value. Simply hold the tool parallel to the floor covering and trim off the carpet tufts on top. Because it is flat it will ride easily above the carpet to put the blade in the right height.
Not only is creased, loose carpeting unsightly, but also it is a pain likely to cause tripping as you walk on it. Fortunately, the task of stretching it can be handled by any committed homeowner. A knee kicker is one special tool that makes the technique quite easy and leaves satisfying results.
It is often used along the walls or any section of the room in the house. As the installation continues you can do the laying down much faster and comfortably. It features teeth that need to be positioned well by pushing the kicker down to the carpeting. If not done the right way however it will only be a waste of your energy and time.
The cushioning added on it enables you to knock your knees to attain the wanted results. Slamming the middle of the knees into it would undoubtedly hurt. Alternatively, use the space above the knee to create more force. This process might need a few kicks in every area to put the carpeting in the right place.
While most parts of a home need tack strips, some areas including stair landings and steps need glue-down installation only. The notched trowel is used to spread adhesives that are rated for carpets in such spots. It combs the materials onto the surfaces properly despite the depth or thickness of the covering. Using the rightly sized one ensures the right amount of glue is smeared. And in the end, you get to work down into the carpet and smoothly tugging the pieces. If some part of a seam feels loose on any joined edge, you can get back to that point and seal it.
The installation process for a wall-to-wall carpet involves stretching. In addition to hooking the strips with a knee-kicker on one side, the other end needs a stronger tool to tightly stretch the carpet. A power stretcher comes in handily, especially for large floors. This tool is not complex, but very easy to operate if you comprehend its structure and the procedure to be followed when stretching the cover.
Cutting a carpet seems like a simple task sometimes. But to get this job done the right way some art is needed. Whether putting in a news one or pulling up the old piece, knowing the best points to cut saves you time and cost. The important thing to think of is to always use a tool that is sharp enough. This will enable you to operate not only quickly but also with the required control and accuracy. Further than the tool, you simply must take enough time to prevent mishaps on the edges and watch the carpet blend effortlessly to the layout of the rooms.
Most carpet flooring installations involve two carpet pieces getting aligned and attached to another. The point where both meets are known as a seam. Gluing often helps the installers to bring the pile together and avoid having a showy end. This tool makes the seaming procedure easy. In the end, everything remains pressed into the tape and the irregularities smoothened and flattened.
Larger rooms in the home need seaming tapes when installing a carpet. Fortunately, heating the seams is not a hard task anymore. All you need is to take enough time and get the process done the right way. To reduce the chances of having visible ends it is worth putting the pieces away from the main sources of light including doors and windows. Using a seaming iron ca help in melting the adhesive and get both edges held securely.
Carpeting is often installed to make the house and rooms feel warm. When flooring properly cushioning the underlay makes the material long-lasting, very comfortable, and offers high sound insulation levels. Generally, to achieve this there is a need to stretch and attach the carpet well when fitting it. A carpet tucker is a right tool made to cover any space between the walls and floors comfortably.
Fastening plays key roles during the installation process of carpets in the stairs. This way you securely hold the top and bottommost and anchors the insulation tightly on stair steps. From before staples have been used on the edges to bring the pieces together. And it has proven to function well in combination with, or as an alternative to, the tackles carpets. Although, the good thing is that you can use staplers alone to fasten the pad onto the floor.
When stretching or gluing carpeting at home, carpet trimmers are a must-have tool. Cutting the edges around provides an amazing finished look. Although utility knives also perform this task, the design that a carpet trimmer has makes it the best choice. With this tool, it is much easy to cut through the pile of carpet within one movement. You can adjust its height to suit any thickness. What is more, you can sharpen to get a smooth and straight cut.
Poorly seamed carpeting looks disordered. And without cutting and joining the edges well the flooring can start to loosen due to wear. Once you have positioned the pieces it is necessary to determine whether you will seam using an adhesive or using an iron. The truth is both techniques work well.
Depending on the one you decide on, combining it with a heavy-duty carpet roller will make the process very comfortable. This tool will properly smoothen your newly placed carpet. The remaining sealers need to be cleaned up using the recommended cleaner on the label. As the adhesive becomes dry, you can also brush your carpet with a soft brush to enable you to completely cover the seam.
Finally, when you have a large-scale home project like carpet installation it can turn out to be complicated. Although the task can be a DIY, you are exposed to self-injury and loss. It does no harm calling up a professional to take the process on well.
Generally, an understanding of the procedures and getting the right tools are necessary. That said, you can participate and handle this alone and successfully. Finish up the process to have neat looking seams and floor.